PIC16F1526-I/PT【PDF 19/94 页】MCU 14KB FLASH 768B RAM 64-TQFP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3876

15页 16页 17页 18页 [19页]20页 21页 22页 23页

188

7810C–AVR–10/12

Atmel ATmega328P [Preliminary]

Bit 5 – UDREn: USART Data Register Empty

The UDREn Flag indicates if the transmit buffer (UDRn) is ready to receive new data. If UDREn

is one, the buffer is empty, and therefore ready to be written. The UDREn Flag can generate a

Data Register Empty interrupt (see description of the UDRIEn bit). UDREn is set after a reset to

indicate that the Transmitter is ready.

Bit 4 – FEn: Frame Error

This bit is set if the next character in the receive buffer had a Frame Error when received. I.e.,

when the first stop bit of the next character in the receive buffer is zero. This bit is valid until the

receive buffer (UDRn) is read. The FEn bit is zero when the stop bit of received data is one.

Always set this bit to zero when writing to UCSRnA.

Bit 3 – DORn: Data OverRun

This bit is set if a Data OverRun condition is detected. A Data OverRun occurs when the receive

buffer is full (two characters), it is a new character waiting in the Receive Shift Register, and a

new start bit is detected. This bit is valid until the receive buffer (UDRn) is read. Always set this

bit to zero when writing to UCSRnA.

Bit 2 – UPEn: USART Parity Error

This bit is set if the next character in the receive buffer had a Parity Error when received and the

Parity Checking was enabled at that point (UPMn1 = 1). This bit is valid until the receive buffer

(UDRn) is read. Always set this bit to zero when writing to UCSRnA.

Bit 1 – U2Xn: Double the USART Transmission Speed

This bit only has effect for the asynchronous operation. Write this bit to zero when using syn-

chronous operation.

Writing this bit to one will reduce the divisor of the baud rate divider from 16 to 8 effectively dou-

bling the transfer rate for asynchronous communication.

Bit 0 – MPCMn: Multi-processor Communication Mode

This bit enables the Multi-processor Communication mode. When the MPCMn bit is written to

one, all the incoming frames received by the USART Receiver that do not contain address infor-

mation will be ignored. The Transmitter is unaffected by the MPCMn setting. For more detailed

information see “Multi-processor Communication Mode” on page 185.

19.10.3

UCSRnB – USART Control and Status Register n B

Bit 7 – RXCIEn: RX Complete Interrupt Enable n

Writing this bit to one enables interrupt on the RXCn Flag. A USART Receive Complete interrupt

will be generated only if the RXCIEn bit is written to one, the Global Interrupt Flag in SREG is

written to one and the RXCn bit in UCSRnA is set.

Bit

321

RXCIEn

TXCIEn

UDRIEn

RXENn

TXENn

UCSZn2

RXB8n

TXB8n

UCSRnB

Read/Write

R/W

Initial Value

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式